How to Replace a Kia Sportage Replacement Key

For a number of Kia models, the key contains a built-in keyless entry system. The key is usually akin to the remote control and is able to be replaced with a new one from a Kia dealer or locksmith.

Key fobs may stop working due to a variety of reasons, such as an inactive battery, worn out buttons, signal interference or water damage. Here are some suggestions to assist you in getting your Kia sportage replacement key working again.

How do you replace the remote key or smartkey?

It doesn’t matter if your Kia is equipped with an intelligent key, remote key push-to-start keys, or a regular non-transponder steel key, the battery in these keys will eventually require replacement. This is particularly when the car displays a message indicating that the remote or smart key has a low battery.

It’s an easy process. To replace the battery on the keyfob take out your mechanical key from the slit on the back of the fob. Then, pry the cover open. A small screw is found inside the key fob, which holds the battery in place. Utilizing a small screwdriver loosen the screw and remove the battery that was in place. Insert the new battery and then close the cut on the key fob.

When the key fob is equipped with an updated battery Test it by pressing the lock and unlock buttons. You’re good to go when the doors lock or unlock as expected. You can now make use of the Kia’s hands-free lock/unlock feature when your fingers start to get cold or you have to do some errands in Brandon.

Note: Some key fobs (transponder chip or smart keys) may require their programming completed. This requires a programing machine that is only available to the locksmith who works for the automotive dealer. Other keys (non-transponder metal keys) do not require programming. If you’re looking to reprogramme your key, you’ll have to note the key code number on the key code tag.

How to replace the battery

If your Kia key fob isn’t responding when you press the lock or unlock button on the fob, it is a sign that the battery should be replaced. A weak battery can cause other issues like the check engine light flashing on or a delay in cranking the engine. Fortunately replacing the battery on the key fob is a relatively easy DIY project that requires only the most basic tools.

Before you begin be sure that your vehicle is off and that all doors are closed. Find the small, metal or plastic piece on the bottom of your key fob, and jiggle it until a metal key is released. This key can be inserted into the driver door handle to unlock your car.

To replace the battery inside the key fob remove the rear cover. Use a pry tool to loosen the latch that holds the black negative cable. Remove the old battery and then orient the new battery in a way that the “+” positive side is facing you, and the “-” negative side is facing the fob’s metallic electrical contacts. Avoid using too much force when pushing the new CR2032 into place to avoid breaking or bending the steel contacts.

After you have installed the new battery and turning the key fob on and off in the ignition until the door locks cycle. You can then test your Kia’s key fob to ensure it’s working as intended.

How do you replace a keyless keys

Depending on the model of your Kia Sportage, you may have a standard key fob or a smart key. The smart key comes with an embedded mechanical key blade, while the standard keyfob does not. Both key fobs are equipped with batteries that eventually need to be changed. This is a simple procedure that takes only two minutes.

Before you get started it is important to make sure that you are on a flat surface with good lighting and that your Kia is off. Be aware that there are tiny pieces inside the fob which could be snagged if not vigilant.

The first step is to locate the small release button that is located on the lower backside of the fob. It will be either an oval silver button or a rectangular slot. Once you press this button, the mechanical blade will appear and you can then open the key fob.

Once you have the key fob open it is easy to remove the old battery, and replace it. The new battery is a CR-2032 that can be purchased online or at a local auto parts store. When you’re done, the key fob should allow you to lock and unlock your vehicle, even if it isn’t running.

How do you replace the mechanical key?

The Kia keyfob is a great convenience that lets us lock or unlock our car by pressing the button. As with all devices like a key fob, the Kia might have issues. There are ways to solve these issues and keep your key fobs working for the duration of.

A dead or low-quality battery is one of the most common problems. This can cause the device to stop working completely or to work intermittently. If this is the case then replace the battery with an entirely new battery.

If kia duplicate key does not solve the issue, use an ordinary screwdriver with a flat head to push the plastic casing of the fob open. Be careful not to damage any internal components or scratch the plastic. When the battery is open, carefully take off the battery you have been using and replace it with a new one.

Close and open the door using the mechanical key. (Every Kia fob comes with an emergency mechanical key which will fit into the slot). Test the key fob and ensure that it’s working properly. Contact a dealer, or a locksmith to fix the issue in the event that the key fob is not working. To avoid lockouts in the future, ensure you purchase an emergency key that will work in all of the trunk and door cylinders.